Posts by secure_admin

Why Irrigation is Beneficial

»Posted by on May 5, 2017 in irrigation | 0 comments

You must be thinking that building an irrigation for your plants in the backyard is a waste of water and energy. However, there are a lot of things you could benefit out of building a good irrigation. Written below are some of the benefits one could get from building a good and effective irrigation.

irrigation

Healthy Landscape and Water Bill Maintenance

A lot of owners of residential and commercial property necessarily use a great amount of water to keep grass and landscape fresh and healthy, costing them bigger money than usual.

Systems of irrigation could be very efficient than any other kinds of watering. That is, sidewalks or missing patches of green turf could be unnecessary when irrigation exists in your household. Irrigation will put the exact amount of water in the right spots especially when where it is needed.

That is, you get to have a balance that hoses or sprinklers couldn’t have. This is important, especially when your lawn is a reflection of you as a homeowner.

 

General Water Management

A lot homeowners use a great amount of water in order to maintain their landscapes green and fresh. Learning to properly water your lawn with the use of a watering system such as irrigation wouldn’t just save you money but it could also help maintain and conserve water in the long run which is not only good for your but also to the people of the future generation.

Watering Schedule Recommendation

  • Established Lawns

If your lawns are established, you may be required to use far less water than sodded or freshly seeded lawns. For cooler seasons, decreased daily watering is necessary. That is, you may need to water your plants every other day.

However, when it is during a hot season, watering a plant five to six times a week is highly recommended. Watering a plant from three to six in the morning is one of the most ideal type to water the plants. This is because this is the time where water infiltrates the most.

 

  • Sod

When you have a newly installed sod, it is recommended that you water your plants at least two times daily. However, when it’s a very hot season, another water cycle could be necessary. When the period of growth when only a few weeks has passed, reducing the water frequency is necessary.

When you have a good irrigation system in your house, you don’t only have to experience its benefits but also you could save so much energy and water in the long run. Moreover, you don’t have to just experience the beauty that it brings to your plants but on your home in general.

To help you build the best irrigation that suits your home, it is good to hire an arborist in Birmingham, AL, those professionals that are expert in the field of taking care of plants and trees. This is not just to build a good and effective irrigation but it is also beneficial for the plants that you are planning to have in your backyard.

 

read more

Steps On How To Stain The Floor

»Posted by on Apr 20, 2017 in acid, floor, stained | 0 comments

If you had the chance to look at amazing acid stained floor, we are sure that you are already dying to make your floor like that right now. So we are going to tell you the steps that you should do to stain and seal your floor and make it more beautiful. Please follow the steps loyally so that you can achieve the best results like those done by experts like concrete staining at the end.

floor

First step: The concrete should be cured

When your concrete floor is freshly poured then you must let it cure for only five to six weeks before acid staining it and sealing it right after. The seal will not take effect when you do not let the freshly poured concrete after applying it.

Second step: Wash the surface well

The surface before acid staining it should be very clean. It should not have any debris, waxes, paints, grease or any dirt. There are many products in the market that you could use in order to clean the surface very well.

Third step: Concrete stain

You should be able to choose the perfect concrete stain for you. The best ones are those which are made of water-based dye for the stain and you can apply these with sprayers that does not have air or even just the common gardens sprayers. Do not settle for one, for you to achieve the color that you want, you should apply a number of colors to achieve the desired effect on your concrete floor. You can check the guide from the stain that you have bought so that you can know which better things to do to deal with the stain.

Fourth step: Washed surface

When the stain is already dry then it is time for you to wash it again so that there are no remaining stains that are still on the surface. The cleaner that you should use is a neutral cleaner so that it would not affect or it would not react with any of the substance that you put in it. A stiff bristle brush or scrubbers are just few of the tools that you can use in order to clean the entire surface. This step should not be forgotten if you really want to achieve a nice effect.

Fifth step: Dry the surface again

Again, let it dry completely so that there will be no blushing effect on the floor. This only happens when the surface is damp so you really need to let it dry.

Sixth step: Seal it with two coats

The sealer that you bought can be applied using a brush or a roller depending on your preference. Before you apply the second coat, make sure that the first coat had dried completely so that it will not appear patchy and the second layer of the sealer would appear nicely and make the whole floor shiny. And after applying both of the coats allow it to sit for four hours before stepping on it or coming in contact with your floor. Give it at least four days in order for it to fully cure.

 

read more

Sealing the Acid Stained Floor

»Posted by on Apr 20, 2017 in acid, floor | 0 comments

There is beauty when your concrete floor is acid stained because it becomes a marble-like pattern on the surface of the floor but you also have to protect it and for you to do that, you must seal it so that it would also look shiny. The efflorescence that it creates is due to the hydrochloric acid solution reacting to the minerals in the concrete floor because it gets the carbon dioxide that is present the air around you. Efflorescence refers to the variety of color tone in your concrete. Instead of having just an ordinary concrete, you can have an acid stained floor to make it unique and very nice to look at.

stained floor

The things that you need to do it are paint tray, paint liner, polyurethane sealer, big brush, roller refill that is smooth in the surface and a paint roller. And remember that you should always seal the whole concrete floor after staining it with acid so that it will look shiny and it will not be destroyed over time.

Here are some of the steps that you should do in order to seal the acid stained concrete that you have.

1st: Make sure that the entire room is well ventilated. You can open the doors and the windows or if possible, turn on your electric fan so that you can have more air in the room.

2nd: Clean the floor very well when the acid is fully dried after the acid staining. Make sure that there is not any debris that is present in the floor while sealing it.

3rd: Prepare the tools like the sealer and the roller. Also, shake the polyurethane sealer very well so that it will be the perfect mixture before applying it. The paint tray that you are about to use should have a liner in it and put a perfect amount of it inside the tray.

4th: Start at the perimeters. The large brush is very useful in putting at least three inches of strip around the sides or the perimeter. This secret is very useful in order for your roller not to come in contact with the wall. Make sure that the sealer is very smooth and even.

5th: When you have finished the edges of the room, then you can start sealing the rest of the room starting from the exit and work your way inside. Take off the excess sealer on your roller so that you will not be worried about the excess products so take it off all of the excess. You do not want anything dripping on the floor. Some bubbles may be present so go it over your brush. Do not rush on the process; you want to make sure that the seal you are applying is uniform around all the surfaces.

6th: You should let the seal dry and add the next coat only when it is completely dry, still using all of the steps above.

The seal is really important so that it would act as a protection to the concrete floor and it will highlight the pattern that it produces after the acid staining process.

 

read more